Ftdi Ft232r Usb Uart Ttl Poort Cable - Iskra Kamstrup Landis Dutch Smart Meter Dsmr P1 E350
SKU #4939893375012
Type: System & Power Cables
Availability: In Stock
Prices starting from: Kr 284.41
FREE TRACKED SHIPPING WORLDWIDE
Specifications:
Cable length:180CM
Signal: TTL 5V level
Chip: FTDI FT232R
This cable is specially for the Dutch Kaifa Smart Meter
Communication with Domoticz on Raspberry.
FTDI FT232R USB TTL5V to RJ11 6P6C Cable
for ISKRA AM550 kaifa ma105 Iskra ME 382 Kamstrup 162 382 en351 Landis + Gyr E350 P1 Poort Slimme Meter
The P1 port, which is the RJ-11 connection, has the serial protocol where standard IEC-62056-21 is used.
Schematische voorstelling P1 poort (ESMRv5.0 P1)
Note: Does not include the Dutch Smart Meter
The P1 port is a 6p6c socket, commonly referred to as RJ12. The RJ11/RJ12 plug is the one we have known for years as the telephone plug. You can go with an RJ11 plug that has only the 4 middle pins connected, but your best option is to use an RJ12 connection with all 6 wires connected. That way you can optionally use the power output from the P1 port to power the reading device. The 6 pins of the P1 port are wired as shown in the table below.
Specifications:
1 +5V Power supply line (250mA)
2 Request Data request (high)
3 Data GND Ground for the data signal
4 N.C. Not Connected
5 Data Serial data output signal
6 Power GND Power ground
Pin 4 is not used.
Pin 1 and 6 provide power that can be used by a connected device. According to the DSMR 5.0 standard, this output is capable of providing 250mA at 5V. This power output was not available pre-DSMR 4. But the 4.x.x standard does not give details of its maximum load, only the DSMR 5.0 standards description.
Pin 5 and 3 are the serial output pins and provides a logical 1 with an output voltage of less than 1V, and a logical 0 with an output voltage of more than 4V. This is commonly referred to as TTL Serial. The Landis meter has an open collector output (pin 5), meaning that we need to add a pull-up resistor of 1-2k to allow the data output to switch between these states. Note that the output is inverted, so we'll have to invert the signal by software or hardware. The baudrate is 115200 bps with 8 bits, no parity and 1 stop bit (8N1). Up to DSMR 3.x the rate was only 9600 baud.
Pin 2 can be used to control the dataflow from the meter. Make this pin high (>4V) to have the meter send it's data on the data output pin. You can either make this permanently high, resulting in a constant flow of meter data every 10 seconds, or only when you want to request data. To stop receiving data, an OSM needs to drop the “Data Request” line - that is, set it to “high impedance”. Data transfer will stop immediately in such case. For backward compatibility reason, no OSM is allowed to set “Data Request” line low (set it to GND or 0V).
Product doesn't match the description? Contact us within 30 days after you receive it!
In case of cancellation, money will be refunded to your account within 3 days.
Cable length:180CM
Signal: TTL 5V level
Chip: FTDI FT232R
This cable is specially for the Dutch Kaifa Smart Meter
Communication with Domoticz on Raspberry.
FTDI FT232R USB TTL5V to RJ11 6P6C Cable
for ISKRA AM550 kaifa ma105 Iskra ME 382 Kamstrup 162 382 en351 Landis + Gyr E350 P1 Poort Slimme Meter
The P1 port, which is the RJ-11 connection, has the serial protocol where standard IEC-62056-21 is used.
Schematische voorstelling P1 poort (ESMRv5.0 P1)
Note: Does not include the Dutch Smart Meter
The P1 port is a 6p6c socket, commonly referred to as RJ12. The RJ11/RJ12 plug is the one we have known for years as the telephone plug. You can go with an RJ11 plug that has only the 4 middle pins connected, but your best option is to use an RJ12 connection with all 6 wires connected. That way you can optionally use the power output from the P1 port to power the reading device. The 6 pins of the P1 port are wired as shown in the table below.
Specifications:
1 +5V Power supply line (250mA)
2 Request Data request (high)
3 Data GND Ground for the data signal
4 N.C. Not Connected
5 Data Serial data output signal
6 Power GND Power ground
Pin 4 is not used.
Pin 1 and 6 provide power that can be used by a connected device. According to the DSMR 5.0 standard, this output is capable of providing 250mA at 5V. This power output was not available pre-DSMR 4. But the 4.x.x standard does not give details of its maximum load, only the DSMR 5.0 standards description.
Pin 5 and 3 are the serial output pins and provides a logical 1 with an output voltage of less than 1V, and a logical 0 with an output voltage of more than 4V. This is commonly referred to as TTL Serial. The Landis meter has an open collector output (pin 5), meaning that we need to add a pull-up resistor of 1-2k to allow the data output to switch between these states. Note that the output is inverted, so we'll have to invert the signal by software or hardware. The baudrate is 115200 bps with 8 bits, no parity and 1 stop bit (8N1). Up to DSMR 3.x the rate was only 9600 baud.
Pin 2 can be used to control the dataflow from the meter. Make this pin high (>4V) to have the meter send it's data on the data output pin. You can either make this permanently high, resulting in a constant flow of meter data every 10 seconds, or only when you want to request data. To stop receiving data, an OSM needs to drop the “Data Request” line - that is, set it to “high impedance”. Data transfer will stop immediately in such case. For backward compatibility reason, no OSM is allowed to set “Data Request” line low (set it to GND or 0V).
WARRANTY
We'll refund your money if the item hasn't been delivered within 40 days after purchase. You have 2 weeks to request a refund — until day 60.Product doesn't match the description? Contact us within 30 days after you receive it!
In case of cancellation, money will be refunded to your account within 3 days.
REVIEWS
Very Fast Delivery. 11 Aug 2020 11:21
Shopper from NETHERLANDS
SIMILAR PRODUCTS
Cable Cord For Dc Power Connector And Jack Adapter
FREE SHIPPING
1.5meter 250v 2.5a-flexible Electric Power Cord
FREE SHIPPING
Strimer Plus Triple Motherboard Extension Rgb Cable
FREE SHIPPING
Iec 320 C13 Female To C14 Male Pdu Angle Power Cables - Power Cord Adapter
FREE SHIPPING
6es5734-1bd20, Pc To Tty Adapter Programming Cable For Simatic S5, Plc 6es5, 734-1bd20
FREE SHIPPING
Male Plug To Female Socket Power Extension Cable For Pc Computer
FREE SHIPPING
Usb Power Cable-electronic Data Line
FREE SHIPPING
1pcs Flat Cables Dvd, Scanner, Printer Avh 3500/3550/3580
FREE SHIPPING
Cylindrical Emi Suppressor Ferrite Core Filter For Data Cables
FREE SHIPPING
Led Connector Kit With T & L-shaped Strip Jumpers /wire Connection Terminal
FREE SHIPPING
2 Pin Prong Eu Cable Power Supply Console Cord C7
FREE SHIPPING
Usb Male To Ps/2 Ps2 Female Converter Cable Adapter
FREE SHIPPING
2 In 1 Usb Charger Data Transfer Cable
FREE SHIPPING
2 In1 Usb Charger Cable, Transfer Data Sync Cord Line Power Adapter Wire
FREE SHIPPING
Male Head Power Adapter Suitable For Lenovo Thinkpad
FREE SHIPPING
Diy Dupont Jumper Wire Kit
FREE SHIPPING
Hdd Cable Cord For Server Mining
FREE SHIPPING
6pin To 8pin Psu Cable Gpu Psu Server Power Supply Mining Board
FREE SHIPPING
1x To 16x Sata To 6pin Usb 3.0 Cable Riser Card Adapter Mining Miner
FREE SHIPPING